Windy launches Route Planner
Gkikas LGPZ last edited by
Thank you very much for this new feature! You are awesome !!!
a) I, also, preffer "absolute" wind direction and speed.
b) On "VFR" mode, it would be nice to have the ability to input
take-off time, airplane's speed, trip duration.
c) On future high IFR mode, please include a dashed line for areas with wind speed>60 kts (jet stream)
Question: the grey shades correspond to rel. humidity aloft?
rittels last edited by
Will enjoy playing with it.
Congratulations gang for another amazing feature within Windy.....I have long been anticipating something with this type of functionality for forecasting purposes. VERY NICE.
As this is still in development/testing phase, could I add some comments to the general discussion?
You might need to make users aware that the freezing level is "height above terrain". I added an image displaying the freezing level rapidly decreasing with height passing over the NZ Alps. This could cause some concern for a VFR pilot considering Icing conditions overflying elevated terrain when in reality the freezing level could be well above the intended flight path. I did a search through the EC data fields and found no fields that map freezing level abv MSL.
As a future addition....could you include the temp at the corresponding height at the head of each wind barb.
The current freezing level line also gives a wrong indication of snow line across the Alps - it appears as if snow will fall to very low levels over the Alps.
Another comment that I wanted to add.....
Again with VFR option, and in this case concerning Tstorms:
1/ The RH as a proxy for cloud may not always work for cellular convective situations. I have marked out specific regions where the EC model is indicating a line of TStorms on the Rain/Tstorm layer and the Cloud Top layer.....however the RH display in the Route slice only presents cloud below 6000ft. NB: this is consistent with the RH fields found within the area display when you ascend and descend through the available layers. The cloud top layer shows a distinct line of elevated cloud abv 50k ft and would be best avoided.
NOTE: I read in your comments that you will be attempting to add an IFR option for the upper level fields. Could you include a graphical feature OR a line along the bottom of the cross section highlighting "Cloud Top" values???
I would also support upper level isotach lines showing jet streams (80/120/160kt etc) and regions of significant vertical wind shear.
2/ A comment regarding the weather/rainfall along the cross section.....the users need to be aware that the rainfall towers/weather(in this case TS's) are for the previous 3hrs hours from the forecast time. I have highlighted this in top image. Just so the user is not critical of the model output when they see rain/weather at a distance point along the route following a weather system OR think that the weather system providing the precip is some x100km wide.
3/ The cloud base....I'm not a great fan of this field (cloud > SCT) when in the case of these tropical Tstorm situations (see above) the cloud base forecast is >8000-12000ft - which is not the case for this region. I like the addition of the DewPoint spread which as least gives an approximation potential cloud base (1-8 Oktas) -- DewPointSpreadx400ft - and again would be better suited to any VFR pilot.
AND finally.........I can see the benefit of "Relative Wind" vectors from a flight planning perspective. But I would also favour "Absolute Wind" vectors from a forecasting perspective. And the official forecasts are all in Real/Absolute wind directions which would make it easier to evaluate the Windy forecast against other official forecasts.
Thanks for the all the effort.........I look forward to utilising this feature.
Very nice. Simple, intuitive and it does what it is designed to do. Can't ask for more.
A Former User last edited by
It looks great. I am having trouble understanding what it is showing. It only shoed 2 miles of a 10 mile trip. Probably driver error.
edson.eustachio last edited by
Congratulations! The new feature is very nice.
I've been using Windy for simulating sailing routes based on the wind information presented by the previous version of the distance and planning functionality.
The new feature is great but I when I tried to trace those routes using the new version, I could not because now I'm no longer able to see the pointer coordinate while a drag it over the map. Another missing information for me is the angle of the segment in the route map,.
It would be great if those information were available in the new version, as well.. Or maybe, it could be available a way to access the old version.
I hope those suggestions make sense for you guys and thanks a lot for delivering this amazing tool.
marekd last edited by
@Gkikas-LGPZ Yes, it is RH.
@stitch Thank you for your valuable feedback! We will think about it.
@edson-eustachio Did you try to click on "Route detail" button on the bottom left? :-)
mteugels last edited by mteugels
Great feature ! I can use it in General Aviation/ Gliding . On long stretches , a timeframe would definitely be needed , so an ETA or time en-route of average ground speed would be needed to make it really useful for planning . I like the convective cross-cut very much ! As for the wind , well , I personally would prefer oriented to the north . If one prepares ones flight , other softwares would take into account the head/tail component , this would be too far-fetched for Windy I believe
peterk last edited by
I like the principle of it and it's really useful to see the forecast in this format however I think it's lost some essential functionality.
On the previous version you could plot a route and move points to the correct lat long positions. The route details gave a list of the positions and distances however the figures changed as the points were moved. With the new update you have to guess the correct lat long and keep pressing route detail to see the current position, move the point and then go back to check the route details etc. Would it be possible to combine some of the old functionality into the new update? It would also be useful to be able to change the unit of distance to nautical miles which is more relevant for sailing.
igor 320 last edited by igor 320
All winds are relative to the direction of movement, i.e. the green arrow pointing to the right is a tailwind, the red arrow pointing to the left is a headwind. Should we change it? Would you prefer switching between relative and absolute wind direction?
You can make the same stuff used in GRAMET (aka vertical cut of the GFS forecast). This will help users to avoid learning new symbology if they wish to compare both forecasts.
Throughout the chart, you will find a grid of wind symbols. These give you a lot of information. The circle in the middle shows the cloud coverage in quarters, in the above example there would be no clouds. The barb attached to the circle is the wind rose with the standard symbol. The above example shows 35 knots and 30 knots of wind coming from north. The magenta array shows the aircraft’s movement relative to the direction of the flight (hence magenta, that used as standard color in avionics to indicate flight track). In this example the aircraft flies on a north easterly course and would experience a headwind coming from the left. The number right to the wind symbol is the temperature, -47°C in our example.
Add a full-screen option to have more complete view.
Change the color of altitude marks (so they could be visible on dark & white background) and make them still at the same position (right now they shift to the left).
Route details should be editable with keyboard input & coordinates should be switchable in settings (from DEG°MIN'SEC'' to decimals XX.XXXXXX°).
Add an option to save routes in your profile and make them constantly visible (right mouse click/long tap on the route to hide or close it). At this moment if you hit 'X' on the vertical cut pane, the route disappears. You don't always want to observe the vertical part, because it 'eats' a big bite of display. That will be especially useful when you fully implement it into the app to help pilots get better weather visualization when they're in the air (see my next suggestion).
A copy/paste of my old suggestion suggestion:
The app lacks speed control compared to web-version and I also would like to see more frames per time unit (right now it refreshes with a speed of 1 frame/3 minutes). Maybe you can make another time period in addition to 12/6/1 hour, say, for the latest 15 minutes which will be the most frame-dense period (for ex. 1 frame/minute) ? When pilots are already in the air, they're interested only in very latest weather data and 15 minutes may serve this need well.
I usually fly at lower altitudes and can receive mobile broadband connection from time to time (depending on my location) and an option to reduce downloadable traffic is highly demanded. Maybe you can make an option to preload specific part of the map (just like in Google maps) and fine-tune overall downloadable traffic to reduce unnecessary stuff. Again, the goal is to receive fresh & updated data as soon as your phone/tablet receives broadband connection , because it may be lost in next minute.
These are just a very brief quick-notes. I'll try to thoroughly test it later.
Aquamante last edited by
Very nice and useful feature!
I want to use it as sailor, but I don´t understand the wind direction arrows. On my opinion, they don't match with the wind direction of the windflow, (or I'm not using it correctly?).
If you read this topic from beginning you should understand what wind arrows show.
edson.eustachio last edited by
@marekd Hello Mark. Thanks for your answer.
Yes, I did try to use the "route detail" button. It saw it shows the pointer coordinate but this feature does not show the pointer coordinate while I drag it over the map. I using this feature to locate an specific point in the map based on a given distance and angle of navigation. This distance and angle are calculated by my sailing simulation.
JRep65 last edited by
@marekd - THIS will be interesting to watch!
Hi guys, on your VFR route cross-section, and I right in saying that the highest "Dew-point spread" value presented is 5°C?
Could you increase the highest value to say 12°???
This would give an estimated cloud base height range [when looking at boundary layer cloud physics] up to ~5000ft (or up to the CAVOK cloud base height) when using the following rule....." The difference between the dry adiabatic lapse rate and the rate at which the dew point drops is around 8 °C per 1,000 m. Given a difference in temperature and dew point readings on the ground, one can easily find the LCL by multiplying the difference by 125 m/°C (410ft/C°) - from Wikipedia".
albi last edited by
I like the route planner, but I also like to keep the distance measure as it was before, especially being able to see the distance line from point to point even across the international dateline. Also, with the new route planning window it literally takes up the bottom half of my laptop screen which substantially decreases the visible map area. Is is possible to minimize the route planner dialogue box without exiting it? thanks.
PeterDotselaere last edited by
Would be nice to see the coordinates, as before
sebn last edited by
great feature! Like Igor said: "Add an option to save routes in your profile and make them constantly visible" - yes please!
Also I´d love to see a function to generate a PDF for offline use / archival issue for flying (proof of weather flight planning).
A button to quickly invert the route might be interesting as well (we officially have to do a weather briefing for every leg).
marekd last edited by
Thank you all for your feedback. We are working on next version and we read your posts carefully.